FANUC SYST alarm codes
248 alarms · Liste des alarmes FANUC SYST — description et remède.
SYST-001PAUSE HOLD button is being pressedSYST-002PAUSE HOLD is locked by programSYST-003WARN TP is enabledSYST-004WARN SOP is enabledSYST-005WARN UOP is the master deviceSYST-006WARN KCL is the master deviceSYST-007WARN NETWORK is the master deviceSYST-008WARN Nothing is the master deviceSYST-009WARN Safety Fence openSYST-010WARN Max num task reachedSYST-011WARN Failed to run taskSYST-012WARN Not in remoteSYST-013WARN Invalid program numberSYST-014WARN Program select failedSYST-015WARN Robot Service Request failedSYST-016WARN ENBL signal is offSYST-017WARN Single step operation effectiveSYST-018WARN Continuing from different lineSYST-019WARN Program not selectedSYST-020WARN Program not verified by PNSSYST-021WARN System not ready, press resetSYST-022WARN PNS not zero, cannot continueSYST-023SYSTEM Teach Pendant communication errorSYST-024WARN PNSTROBE is OFF. Cannot start execSYST-025WARN Teach Pendant is different typeSYST-026WARN System normal power upSYST-027PAUSE HOT start failed (Error:%d)SYST-028WARN (%s) Program timed outSYST-029PAUSE Robot was connected (Group:%d)SYST-030PAUSE Robot was isolated (Group:%d)SYST-031SYSTEM F-ROM paritySYST-032WARN ENBL signal from UOP is lostSYST-033WARN SFSPD signal from UOP is lostSYST-034WARN HOLD signal from SOP/UOP is lostSYST-035WARN Low or No Battery Power in PSU.SYST-036WARN Semi power failure recoverySYST-037ABORT Key switch brokenSYST-038PAUSE Operation mode T1 SelectedSYST-039PAUSE Operation mode T2 SelectedSYST-040PAUSE Operation mode AUTO SelectedSYST-041PAUSE Ovrd Select could not ENABLEDSYST-042PAUSE DEADMAN defeatedSYST-043PAUSE TP disabled in T1/T2 modeSYST-044SYSTEM (Abnormal) TP disabled in T1/T2 modeSYST-045PAUSE TP enabled in AUTO modeSYST-046SYSTEM Control Reliable/CE Mark config mismatchSYST-047WARN Continuing from distant positionSYST-048ABORT NECALC couldn't get work memorySYST-049ABORT SFCALC couldn't get work memorySYST-050WARN Invalid time in trigger requestSYST-051PAUSE SYTG overrun: %d %d %x %d %dSYST-052WARN Trigger slot already used: %dSYST-053WARN Invalid fast_DIN no: %dSYST-054WARN Event-ID already used: %dSYST-055WARN Event-ID not found: %dSYST-056WARN Scan routine list fullSYST-057WARN Illegal intervalSYST-058WARN Duplicate scan routineSYST-059WARN Scan routine not activeSYST-060WARN Duplicate cond/act tableSYST-061WARN Scan table list fullSYST-062WARN Scan table not activeSYST-063WARN Scan time record seq errorSYST-064WARN Bad scan table dataSYST-065ABORT SFCALC overrunSYST-066PAUSE Teach Pendant communication errorSYST-067SYSTEM Panel HSSB disconnectSYST-069WARN Program number out of rangeSYST-070WARN No program name in tableSYST-071WARN Program not foundSYST-072WARN Program not enabledSYST-073WARN Manual selection mismatchSYST-074WARN Karel shell failedSYST-075WARN Shell init failureSYST-076WARN Shell condition setup failureSYST-077WARN Entered INTERLOCK modeSYST-078WARN Entered ISOLATE modeSYST-079WARN Startup check failedSYST-080WARN Fault must be resetSYST-081WARN Not at home positionSYST-082WARN Not within resume toleranceSYST-083WARN I/O is simulatedSYST-084WARN I/O forced unsimulatedSYST-085WARN Gen override not 100%SYST-086WARN Gen override forced to 100%SYST-087WARN Prog override not 100%SYST-088WARN Prog override forced to 100%SYST-089WARN Machine lock onSYST-090WARN Machine lock forced offSYST-091WARN Single step activeSYST-092WARN Single step forced offSYST-093WARN Process not readySYST-094WARN Process forced readySYST-095ABORT Remote diagnose internal errorSYST-096ABORT Designated task is not validSYST-097WARN Fail to initialize ModemSYST-098WARN Card Modem is removedSYST-099WARN Card Modem is not respondedSYST-100WARN DSR in Modem OFFSYST-101WARN Connection is stoppedSYST-102ABORT HDI not recordedSYST-103WARN Not-home ignoredSYST-104WARN Resume tolerance ignoredSYST-105WARN Simulated I/O ignoredSYST-106WARN Gen override ignoredSYST-107WARN Prog override ignoredSYST-108WARN Machine lock ignoredSYST-109WARN Single step ignoredSYST-110WARN Process ready ignoredSYST-111WARN No home pos definedSYST-112WARN No production start input definedSYST-113WARN No style input group definedSYST-114WARN No RSR input definedSYST-115WARN No PNS select input definedSYST-116WARN No RSR echo output definedSYST-117WARN No PNS echo output definedSYST-118WARN No PNS strobe input definedSYST-119WARN No echo strobe output definedSYST-120WARN No style option input definedSYST-121WARN No decision input group definedSYST-122WARN No style output group definedSYST-123WARN No option output definedSYST-124WARN No decision output group definedSYST-125WARN No in-cycle output definedSYST-126WARN No task-OK output definedSYST-127WARN No isolate output definedSYST-128WARN No interlock output definedSYST-129WARN No manual style output definedSYST-130WARN Program still runningSYST-131WARN Invalid manual style requestSYST-132WARN Manual request timed outSYST-133WARN System trigger request earlySYST-134WARN Max. freq. exceeded ch.: %dSYST-135WARN Invalid Clock, Please ResetSYST-136WARN System Time was resetSYST-137WARN Device not foundSYST-138WARN Motherboard not installedSYST-139WARN Invalid motherboard requestSYST-140WARN Invalid IRQ specifiedSYST-141WARN BMON was updatedSYST-142WARN ABS time in sytmrev in pastSYST-143WARN pkt_data_size too bigSYST-144WARN Bad DO specfied by %sSYST-145WARN DO specfied by %s OFFLINESYST-146WARN n_pkts invalidSYST-148PAUSE Dynamic Brake is DisabledSYST-149WARN Dynamic Brake is EnabledSYST-150WARN Cursor is not on line 1SYST-151WARN Start again (%s, %d)SYST-152WARN Cannot force DO’s in AUTO modeSYST-153WARN Cannot SIM/UNSIM DO’s in AUTO modeSYST-154WARN No start in ISOLATE/BYPASS modeSYST-155ABC overrunSYST-156SYSTEM Unknown hard wareSYST-157SYSTEM CE/RIA software does not existSYST-158PAUSE Robot cannot move in T2 modeSYST-159WARN GO %d for Error Output not configuredSYST-160WARN Value outputted to GO %d out of limitSYST-161WARN Cannot start Remote diagnosticSYST-162PAUSE Servo On during Remote diagnosticSYST-163WARN Cannot operate IO during Remote diagnosticSYST-164WARN Teach Pendant communication errorSYST-165PAUSE TP intermittent communication errorSYST-166WARN TP intermittent communication errorSYST-168Robot(G:%d) is isolatedSYST-169WARN S/W Registration is temporarySYST-170WARN S/W Reg. expires in %d daysSYST-171PAUSE S/W Reg. expires in %d daysSYST-172PAUSE S/W Registration has expiredSYST-173WARN See S/W Reg Screen (STATUS)SYST-174SYSTEM Invalid SYST - CTRL start ReqSYST-175WARN System was updatedSYST-176Software was updatedSYST-177RobotLink master is the masterSYST-188book(%d) was not createdSYST-189There is no bookSYST-190HMI Mode - key unavailableSYST-195TP (on Rob#%d) enabled in T2 modeSYST-196Enabled TP exists (H%x)SYST-197Multi-arm Watchdog alarmSYST-198Slave Robot Not ReadySYST-199Def Prog NOT change (TP disbl)SYST-200Only Master TP may FWD/BWDSYST-201Master mismatchSYST-202Incorrect $rmt_master on Slave robotSYST-203Robot #%d has become onlineSYST-204Multi Program start in progressSYST-205NO action specifiedSYST-206Operation canceled by RESET keySYST-207Message posted at Rob#%d (%s)SYST-208Feature NOT supportedSYST-210Process Sync Time-out errorSYST-211Comm processor Time-out errorSYST-212Need to apply to DCS paramSYST-213User power cycleSYST-214DCS ESTOPSYST-215DCS CSTOPSYST-216DCS DCSALMSYST-217DCS pos./speed is not availableSYST-218DCS Unavailable robot model G:%x HexSYST-219Need to verify DCS param (%d)SYST-220Sync Time-out errorSYST-221Sync Schedule mismatchSYST-222Image backup succeededSYST-223Image backup failed(0x%x)SYST-230RCRON: Action successfulSYST-231RCRON: Action failedSYST-232RCRON: Tick missedSYST-233RCRON: No response from MAINSYST-239Auto Software Update failedSYST-242Invalid RPS codeSYST-243RPS failed(%s)SYST-244Auto mode is requiredSYST-245Local mode is requiredSYST-246Teach mode is requiredSYST-247Master ON is requiredSYST-248Alarm conditionSYST-249No system ready inputSYST-250No robot ready inputSYST-251No teach plug ON inputSYST-252Teach plug ON inputSYST-253No safe stop inputSYST-254Safe stop inputSYST-255No Teach OK inputSYST-256Servo OFF inputSYST-257No Ext. Hold Relase inputSYST-258Operator panel holdSYST-259UI signals are disabledSYST-266Please cycle powerSYST-267System is being initializedSYST-268Resume program(%s) executionSYST-269FFR sequence(%s) executionSYST-270Ref. Position maximum exceededSYST-271Lack of MC for savingSYST-272Lack of USB for savingSYST-277BMON update failedSYST-278DCS File is lostSYST-280Operating panel is Teach mode[P]SYST-281Teaching mode input is ON[P]SYST-282Auto mode input is ON[P]SYST-283Don't run program[P]SYST-284Starting Auto Backup[P]SYST-285You can run program[P]SYST-286Ended Auto Backup[P]SYST-287Not enough memory to increase framesSYST-288Write of safety parameter failed(0x%x)SYST-289Request to DCS failed(0x%x)SYST-290Cycle power to use new DCS parameter