FANUC PRIO alarm codes
221 alarms · Liste des alarmes FANUC PRIO — description et remède.
PRIO-001WARN Illegal port type codePRIO-002WARN Illegal port numberPRIO-003SYST No memory availablePRIO-004WARN Too few ports on modulePRIO-005WARN bad port numberPRIO-006WARN bad port numberPRIO-007WARN No match in SET_PORT_ASG de-assignPRIO-008WARN physical ports not foundPRIO-009WARN number of ports invalidPRIO-010WARN bad physical port numberPRIO-011WARN Assignment overlaps existing onePRIO-012WARN Bad board addressPRIO-013WARN No analog input sequence for bdPRIO-014WARN Analog input sequnce too longPRIO-017WARN I/O point not simulatedPRIO-020STOP I/O Link comm error %x, %x, %x, %x (hex)PRIO-021SYST Unknown I/O hardwarePRIO-022SYST Too much I/O data on I/O linkPRIO-023WARN No ports of this typePRIO-033WARN PLC interface init. fault %dPRIO-034WARN PLC interface general fault %dPRIO-035WARN PLC interface serial fault %dPRIO-037SYST Not supported for spec. port typePRIO-063WARN Bad I/O asg: rack %d slot %dPRIO-070WARN PLC interface option not loadedPRIO-072WARN Too many pulses activePRIO-076WARN PLC I/O hardware not installedPRIO-081STOP I/O is not initializedPRIO-083STOP Digital I/O is not recoveredPRIO-089STOP PMC is not supported on this hardwarePRIO-090WARN SNPX communication errorPRIO-091Op panel comm error(ch:%d) %x, %x (hex)PRIO-092Force sensor comm error %x, %x (hex)PRIO-093Fuse blown Rack:%d Slot:%dPRIO-094Overload Rack:%d Slot:%d DO:%d-%dPRIO-095Overload %sPRIO-096SNPX Connection is full<%s>PRIO-097SNPX time out<%s>PRIO-100STOP Model B comm fault %srack:%d slot:%dPRIO-102WARN Cycle power to restart PLC I/OPRIO-104STOP Device is off-linePRIO-106STOP Device with port is off-linePRIO-119WARN Too many DIGITAL I/O portsPRIO-121WARN Stop PMC programPRIO-125SYST SLC2 initialization errorPRIO-126WARN No PMC programPRIO-127WARN PMC file load errorPRIO-128PAUSE T,C,K and D data may be lostPRIO-129WARN SUB%d is not supportedPRIO-130WARN PMC option is not installedPRIO-131WARN PMC file name errorPRIO-132WARN PMC operation is lockedPRIO-133WARN PMC program size is too bigPRIO-134WARN Invalid PMC addr %s%d.%dPRIO-135WARN PMC address is not assignedPRIO-136WARN BYTE access to %s%d.%dPRIO-137WARN BIT access to %s%d.%dPRIO-138WARN %s%d is used in SUB%dPRIO-139WARN Invalid CNC addr %x.%x(hex)PRIO-140WARN Can't display all PMC errorsPRIO-141WARN Invalid PMC programPRIO-142WARN Need E-STOP or CTRL startPRIO-143PAUSE Writting PMC program to ROMPRIO-144PAUSE Faild to run PMC programPRIO-145PAUSE Purging flash file, please waitPRIO-146WARN Flash file purge is completedPRIO-147SYST DIO config file too newPRIO-148SYST DIO config file too oldPRIO-149WARN Invalid assignment recordedPRIO-150STOP CNET Card Init Error Bd %dPRIO-151WARN CNET Internal Error 0x%xPRIO-152WARN CNET Invalid Scan Config Bd %dPRIO-153WARN CNET Conn. Ownership ConflictPRIO-154STOP CNET Duplicate Mac ID Bd %dPRIO-155STOP CNET Network Error Bd %dPRIO-156STOP CNET Er %s Bd %d MAC %dPRIO-157STOP CNET Err Loading BIN file Bd %dPRIO-158WARN CNET File Not FoundPRIO-159WARN CNET Cycle pwr to restart scanPRIO-160STOP CNET Connections Broken Bd %dPRIO-161WARN CNET Network Change OccuringPRIO-162WARN CNET Connections Restored Bd %dPRIO-163WARN CNET Network Change CompletePRIO-164STOP CNET Scan list modified Bd %dPRIO-165WARN CNET Connection Not FoundPRIO-166WARN CNET Invalid Connection TypePRIO-167WARN CNET Vend ID/Prod. Code MismatchPRIO-168WARN CNET Invalid Connection SizePRIO-169WARN CNET Device Not ConfiguredPRIO-170WARN CNET Product Type MismatchPRIO-171WARN CNET Maj/Min Revision MismatchPRIO-172WARN CNET Target App Out of Conn.PRIO-173WARN CNET Needs Network Config.PRIO-174WARN CNET Connection LostPRIO-175WARN CNET Bad Device StatePRIO-176WARN CNET Connection Request FailedPRIO-177WARN CNET Invalid configurationPRIO-178WARN Blk scns lost; %d %d %dPRIO-179WARN Run scns lost; %d %d %dPRIO-180WARN CNET Sys Err %d %d 0x%xPRIO-181WARN CNET Conn. Req. TimeoutPRIO-182WARN CNET CCO Change AbortedPRIO-183WARN Unknown port type namePRIO-184WARN CNET Connection IdlePRIO-185WARN CNET Config Er %d %dPRIO-186WARN CNET Invalid Header sizePRIO-187WARN CNET Invalid Num of SlotsPRIO-188Sim. Skip output not definedPRIO-189(%s^4, %d^5) WAIT will time outPRIO-191AB-RIO Board Init ErrorPRIO-192AB-RIO No Board FoundPRIO-193AB-RIO Failed to Load FWPRIO-194AB-RIO Failed to Start FWPRIO-195AB-RIO Failed to Clear ConfigPRIO-196AB-RIO Config Error, Slot %dPRIO-197AB-RIO Slot %d IdlePRIO-198AB-RIO Slot %d in Test/ProgPRIO-200FIPIO System Error %dPRIO-201FIPIO PCB not installedPRIO-202FIPIO PCB AbnormalPRIO-203FIPIO Duplicate FIP AddressPRIO-204FIPIO Send Buffer ErrorPRIO-205FIPIO Receive Buffer ErrorPRIO-206FIPIO Physical ResetPRIO-207FIPIO BadPrm; CMD %x,%xPRIO-208FIPIO NRDY; CMD %d LNG %dPRIO-209FIPIO Connection BrokenPRIO-210FIPIO Cnf/Adj not availablePRIO-211FIPIO Bad Cnf/Adj statusPRIO-212FIPIO Connection TimeOutPRIO-213FIPIO Connection EstablishedPRIO-214FIPIO Connection RecoveredPRIO-220EGD Producer name/IP not initPRIO-221EGD Consumer size misconfiguredPRIO-222EGD Consumer init failedPRIO-223EGD Producer socket errorPRIO-224EGD System ErrorPRIO-225EGD Consumer timeout - Id:%dPRIO-226EGD Consumer socket create errorPRIO-227EGD Consumer socket bind errorPRIO-228EGD System error - Code:%xPRIO-230EtherNet/IP Adapter Error (%d)PRIO-231EtherNet/IP Adapter IdlePRIO-232EtherNet/IP Not InitializedPRIO-233EtherNet/IP Scn Not in Run ModePRIO-268WARN IO LinkII(M) RX Buf overflowPRIO-280FL-net System Error(%d)PRIO-281FL-net PCB not installedPRIO-282FL-net PCB Abnormal(%d)PRIO-283FL-net IP Address IncorrectPRIO-284FL-net Token Interval ErrorPRIO-285FL-net Init ErrorPRIO-286FL-net Wait Frame StatusPRIO-287FL-net My Node Dupulicate No.PRIO-288FL-net My Node Leave networkPRIO-289FL-net My Node Enter networkPRIO-290FL-net My Node Dupulicate AdrPRIO-291FL-net Node %d Leave networkPRIO-292FL-net Node %d Enter networkPRIO-293FL-net Dupulicate Area Adr %dPRIO-294FL-net Multiple PCBs detectedPRIO-320CC-LK System error(ID=%x)(%d)PRIO-321CC-LK Board not installedPRIO-322CC-LK St.No out of range(%d)PRIO-323CC-LK CRC error(%d)PRIO-324CC-LK Data link error(%d)PRIO-325CC-LK Seq. CPU stopped(%d)PRIO-326CC-LK Seq. CPU abnormal(%d)PRIO-327CC-LK Reg index error(%d)PRIO-328CC-LK AO/R too many(%d)PRIO-329CC-LK AI/R too many(%d)PRIO-330CC-LK PNTtoUOP not enough(%d)PRIO-331CC-LK Reg data invalid(%d)PRIO-332CC-LK no comm. to master(%d)PRIO-333CC-LK comm task failedPRIO-334CC-LK too many boards foundPRIO-335CC-LK different board typesPRIO-350EtherNet/IP Scanner Error (%d)PRIO-351EtherNet/IP Cannot Open SocketPRIO-352EtherNet/IP Cannot Bind SocketPRIO-353EtherNet/IP Send ErrorPRIO-354EtherNet/IP Cannot Resolve NamePRIO-355EtherNet/IP Connect ErrorPRIO-356EtherNet/IP List Serv FailedPRIO-357EtherNet/IP Reg Sess FailedPRIO-358EtherNet/IP FwdOpen Fail (0x%x)PRIO-359EtherNet/IP I/O Timeout ErrorPRIO-360EtherNet/IP Adp Not in Run ModePRIO-369EtherNet/IP System ErrorPRIO-490Modbus TCP Server ErrorPRIO-493Modbus Socket ErrorPRIO-494Modbus Active ClosePRIO-495Modbus TimeoutPRIO-499Modbus System ErrorPRIO-600PNIO board not installedPRIO-601PNIO watchdog alarmPRIO-602PNIO system error(ID=%x)(%d)PRIO-603%sPRIO-605PNIO(D) open error %04xPRIO-606PNIO(D) abort indication %xPRIO-607PNIO(D) offline indication %xPRIO-608PNIO(D) mismatch slot %d %dPRIO-610PNIO(C) open error %04xPRIO-611PNIO(C) alarm indication %xPRIO-612PNIO(C) offline indicationPRIO-613PNIO(C) clear indicationPRIO-615PNIO: can't find the stationPRIO-616PNIO: attach/detach TimeoutPRIO-617PNIO(D) mod plug failed %x %xPRIO-618PNIO(D) submod plug failed %x %xPRIO-619PNIO(C) mismatch st %d slot %d %dPRIO-620PNIO(C) station %d deactivatedPRIO-621PNIO(D) device is not runningPRIO-622PNIO(C) controller is not runningPRIO-623PNIO(C) not in operation modePRIO-624PNIO(C) mod number mismatchPRIO-625PNIO(C) read in completePRIO-626PNIO: please power OFF/ONPRIO-627PNIO: set to operation modePRIO-628PNIO(C) group is not recoveredPRIO-629Restore group manually