ABB Painting process error codes
540 codes · Liste complète — signification et vérifications.
130001Equipment error130002Equipment error130003Trig plane error130004Trig plane error130005Trig plane error130006Trig plane error130007Trig plane error130008Trig plane error130009Trig plane error130010Conv pos out of reach130011Trig counter error130012ConveyorSync Off130013ConveyorSync On130014'Process ready' Timeout130015Conveyor running130500Robot non pressurisé .130501Robot pressurisé .131000Argument error.131001Argument error.131002Argument error.131003Argument error.131004Brush table error.131005Brush number error.131006Argument value error131007Signal 'arg' does not exist131008Applicator number error131009Brushfactor too high131010Brushtable does not exist131011Brushtable not an array131012Wrong datatype for table131013Non-existing signal131014Channel not installed131015Too many trig events131016Illegal value for signal arg131017SetBrushFac: Illegal applicator number131018SetBrushFac: Illegal factor or channel number131019Unexpected IPS return value131020Unknown IPS command sent from RAPID131030Failed to set IPS parameter.131031Failed to get IPS parameter.131050Failed to get index file data.131051Failed to get index file data.131052Failed to get index file data.131400Invalid program mapping index.131401Program mapping missing comma.131500Command toggle was sent before previous command was finished.131501Command toggle was lowered before command was finished.131540Command is not allowed in manual mode.131550Command timed out.131551Command buffer full.131600Motor Modification fault131601Material change error.131602Material change warning.131650No contact with material change engine.131700Maximum negative lag of conveyor reached.131850Bell speed rotation sensor calibration started.131851Bell speed rotation sensor calibration finished.131852Bell speed rotation sensor calibration failed.132000Brush number error.132001Brush table error.132002Brush not activated.132003Equipment Enable rejected132500Unable to open symbol.132501Paint System not inst.132601Process Interface Board fault132602Invalid signal path for signal arg132603Watchdog fault between PIB and MC132604Regained contact with PIB132700Dip in main power voltage, additional energy pack in PDB has been activated132701Main Relay (KA5) conflict on PDB132702Relay KA7 (relay for brake system 2) conflict on PDB132703Relay KA9 (relay for brake system 1) conflict on PDB132999Process error context133000IPS Cfg Error133001IPS Cfg Error133002IPS Cfg Error133003IPS Cfg Error133004IPS Cfg Token Error133005IPS License Error133006IPS License Error133007IPS License Error133008IPS License Error133009IPS License Error133010IPS License Error133011IPS License Error133012IPS License Error133013IPS License Error133014IPS License Error133050Dépasst Temp, capt. …133200arg:Trig error133201arg:Locked133202arg:Disabled133203arg:Disconn.133204arg:Not ready133205arg:Sprv. alarm133206Lock arg failed133207arg:Val hi133208arg:Val lo133209arg:Act.val hi133210arg:Act.val lo133211arg:Comp. hi133212arg:Comp. lo133213arg:Potlife133214arg:Setp. hi133215arg:Setp. lo133216arg:Seq. error133217arg:Unexp. trans.133218arg:Timeout On133219arg:Timeout Off133220arg:No signal133221arg:Max output133222arg:Min output133223arg:Interlock133224Acknowledge needed133225DMC error133226arg .133227Watch dog failure between FPGA and IPS133250arg:Comm. err133251arg:New curve133252arg:Calc. curve133253arg:Resizing133254arg:DMC error133255Apmb error133256arg:Curve err133257SDI error133258VCD error,MacID:arg133259File Access Error133260File Defaulted133261File Parse Error133262New index entry in file133263PPRU CAN Error133264PPRU Error133265SPI down: arg133266SPI up: arg133267Missing index entry in file133268arg: Failed to load brush table.133269arg: Failed to set brush.133270Failed to update IPS parameters133271IPS parameters updated133272Pixel paint cleaning check failure (code arg)133280Servo create error133281Measurement system fault133282Servo drive system error133283Servo calibration done133284Servo calibration error133285Servo calibration timeout133286Servo config. timeout133287Servo coeff. set error133288Servo illegal hardware133300Drive units power up133301SDI Servo WatchDog133302SDI logic +/-15V error133303SDI Comm. error133304Int. Drive unit error133305Drive glitch warning133306Drive unit CBS fault133307Servo temp. warning133308Servo Temp. alarm133309Servo over temperature133310Servo Drive overload133311Servo high voltage133312Servo over voltage133313Servo DC low voltage133314Servo torque command err.133315Servo resolver pos. err.133316Saturated current contr.133317Controller hardware fault133318Servo under current error133319Servo over current error133320Drive unit regulator err.133321Servo max. current error133322Servo unknown error code133323Servo overrun error133324Servo illegal node133325Servo illegal key133326Servo no parameter133327Servo read only par.133328Servo locked parameter133329Servo diagnosis no par.133330Servo current meas. error133331Servo syncslot occupied133332Servo sync insert error133333Servo sync no load par.133334Servo position reg. error133335Servo speed reg. overflow133336Servo speed flt overflow133337Servo res. angle overflow133338Servo resolver error133339Servo torque limit error133340Drive unit comm. lost133341Sms board comm. lost133342Sms board comm. lost133343Sms board comm. lost133344Position step error133345Speed error133430Servo DC-link overtemp.133431Servo bleeder overload133433Servo mains error133434Low DC voltage133435DC-link +/-15V error133436Open circuit in bleeder resistor circuit133437Short circuit in bleeder resistor circuit133501Handler is not calibrated133502Belt on the handler is not calibrated133503Belt calibration error133504Move not allowed133505No servo response on SDI133507Invalid interpolator step133508Servo read error133509Handler not in position133512Command toggle error.133550Joint speed error133551Move not allowed134001Fatal queue error134002Queue overflow134003Invalid token134004Invalid client134005arg can only get master in Auto mode134006arg failed to get master134007arg failed to release master134008Too many subscribers134009Subscriber file error134010Subscriber reference error134011Subscriber unknown error134012Illegal index134013Duplicate entries in file134014First token is not a number.134015Token is not a number134016Fatal parser error134017Buffer full134018Log semaphore timeout134019Master required134020File not found134021Syntax Error134022Duplicate attempt to load program134023Duplicate attempt to load program134024Duplicate attempt to load program134025Material Change Suspended134026Material Change Suspended134027Illegal Material Change Event134028Illegal Material Change Event134029Material Change Resumed134030Material Change Skipped134031Unknown Material Change Error134032Protocol Error134033Enable MaterialSupply Error134034Material Change Time Out134035Invalid material index134036Material Change Error134037Unknown Color Change Error134038Color Change Event Error134039Toggle lowered before command was finished134040Previous command not finished134041Missing Signal Definition134042Volume not recorded134043Color change error134044Material Index out of range134045Illegal process134046Illegal Applicator134047Illegal Applicator134048Illegal Value134049Missing I/O signal134050Program Error134051External Start when no program134052Overpush134053Applicator configuration mismatch134054Command failed in e-stop state134055Configuration error134056Configuration error134057Configuration error134058Configuration error134059XML-parser error134060XML-parser error134061XML-parser overflow134062XML-parser error134063XML-parser error134064CSV-parser error134065CSV-parser error134066CSV-parser error134067CSV-parser error134068Configuration error134070Service routine notification134100CBS servo not enabled.134101CBS restarted while performing operations.134102Unrecoverable CBS error.134103No solution for material index.134104No station for material index.134105No cartridge for material index.134106Not able to empty auxiliary station.134107Storage station is not an IFS.134108Possible CBS collision.134110Safe Move to address failed.134111Safe Move to address failed.134112Safe Move to address failed.134113Safe Move to address failed.134114Move to address failed.134115Move to address failed.134116Move to address failed.134117Move to address failed.134118Servo on failed.134119Servo off failed.134120Calibrate servo failed.134121Calibrate servo failed.134122Set servo acceleration failed.134123Set servo acceleration failed.134124Set servo acceleration failed.134125Set servo speed failed.134126Move arm up failed.134127Move arm up failed.134128Move arm down failed.134129Move arm down failed.134130Move arm up failed.134131Move arm down failed.134132Gripper open failed.134133Gripper open failed.134134Gripper open failed.134135Gripper close failed.134136Gripper close failed.134137Unexpected cartridge presence.134138No cartridge present.134139Gripper sense failed.134140Gripper access check failed.134145Vacuum check error.134146DCU check error.134150Unlock station failed.134151Lock station failed.134152Set primary IFS selector failed.134153Set primary CC selector failed.134154Set secondary IFS selector failed.134155Set secondary CC selector failed.134160Arm sensors bypassed.134161Right gripper sensor bypassed.134162Left gripper sensor bypassed.134163Right cartridge sensor bypassed.134164Left cartridge sensor bypassed.134165Release sensor bypassed.134166Vacuum sensor bypassed.134167Servo position feedback bypassed.134168Servo command acknowledge bypassed.134170CBS configuration error.134171CBS configuration error.134172CBS configuration error.134173CBS configuration error.134174CBS configuration error.134175CBS configuration error.134176CBS configuration error.134177CBS configuration error.134178CBS configuration error.134180Could not set baseplate data.134181Could not get baseplate data.134182Could not get baseplate data.134183Could not get baseplate data.134184Could not get baseplate data.134185Could not get baseplate data.134186Could not get cartridge access data.134187Could not set cartridge data.134188Could not get cartridge data.134189Could not set IFS data.134190Could not get IFS data.134191IFS index from address resolution failed.134192IFS address from index resolution failed.134193Could not get station valve or material data.134194Could not get home address for cartridge.134195No auxiliray station found.134196No storage station found.134200Move cartridge failed.134201Cancel move cartridge failed.134202Exchange cartridge step one failed.134203Exchange cartridge step two failed.134204Exchange cartridge step three failed.134210Move cartridge error.134211Move cartridge error.134212Move cartridge error.134213Move cartridge error.134214Move cartridge error.134215Exchange cartridge error.134216Exchange cartridge error.134217Exchange cartridge error.134218Exchange cartridge error.134219Unexpected cartridge in applicator.134220Unexpected cartridge presence.134221No cartridge found while probing.134222Cartridge must be delivered with right gripper.134223Calibrate servo failed.134224Update servo position failed.134225Resolver CBS fault134226Angle axis position is invalid.134230Integrity check error.134231Integrity check error.134240Maintenance operation error.134241Maintenance operation error.134242Maintenance operation error.134243Maintenance operation error.134244Maintenance operation error.134245Maintenance operation failure.134246Maintenance operation failure.134250Cartridge PotLife timeout.134251Cartridge reached continous use limit.134260Halt exchange timeout.134270DCL pressure release timeout.134300VB Statemachine Suspended134301VB Statemachine Resumed134305VB statemachine aborted.134310DSF cartridge 1 sensor bypassed.134311DSF cartridge 2 sensor bypassed.134312Cartridge 1 home sensor bypassed.134313Cartridge 2 home sensor bypassed.134314Cartridge 1 DSD sensor bypassed.134315Cartridge 2 DSD sensor bypassed.134316Cartridge 1 DSF sensor bypassed.134317Cartridge 2 DSF sensor bypassed.134320Move DSF failed.134321Move DSF failed.134325Move Cartridge failed.134326Move Cartridge failed.134327Move Cartridge failed.134329Get cartridge position failed.134330Restore cartridge positions failed.134340VB configuration error.134341VB configuration error.134342VB configuration error.134343VB configuration error.134350Move cartridge to home failed.134351Move cartridge to DSD failed.134352Move cartridge to DSF failed.134353Move DSF to cartridge failed.134360VB maintenance operation error.134400Out of paint.134401Applicator fill problem.134402Cartridge fill problem.134405Illegal VB state.134406DCL not ready.134410Unknown sensor specified.134411Unknown cartridge specified.134412Unknown position specified.134420Bypass cartridge error.134421Bypass DSF error.134425Unknown DSF position.134426Unknown cartridge position.134430DSF move error.134431Cartridge move error.134432Cartridge move error.134433Cartridge move error.134501Parking unit move error.134502Parking unit move error.134503Parking unit move error.134504Parking unit move error.134505Parking unit move error.134511Cleaning unit move error.134512Cleaning unit move error.134513Cleaning unit move error.134514Cleaning unit move error.134515Cleaning unit move error.134521Applicator chucking failed.134522Applicator chucking failed.134523Applicator chucking failed.134524Applicator chucking failed.134526Applicator un-chucking failed.134527Applicator un-chucking failed.134528Applicator un-chucking failed.134531Parking unit in unknown position.134532Cleaning unit in unknown position.134533Applicator integrity error.134534Applicator integrity corrected.134535Applicator integrity corrected.134536Applicator integrity error.134537Applicator integrity error.134601RCC docking error.134602RCC undocking error.134610RCC movement error.134611RCC movement error.134612RCC movement error.134613RCC movement error.134620RCC cleaning error.134650RCC calibration error.134651RCC calibration error.134700Inkjet image loading failed.134701Inkjet general error.134735Inkjet image loading error.134736Inkjet image loading error.134737Inkjet image loading error.134738Inkjet image loading error.134739Inkjet image loading error.134740Inkjet image loading error.134741Inkjet image loading error.134742Inkjet image loading error.134743Inkjet image loading error.134744Inkjet image loading error.134745Inkjet image loading error.134746Inkjet image loading error.134760Inkjet image loading warning.134761Illegal material operation.134762Illegal material operation.134763Illegal material state.134764Command ignored.134765Command ignored.134766Material recovery state.134767Safety signal for the pump is switched off.134768Safety signal for the pump is switched off.134769Head Power Lost.134770Printer failure.134771No contact with Pixel Paint Gateway app.134772The material supply is not ready to paint.134773Print controller is not ready.134774Pixel Paint integrity check needs to be done.134775Pixel Paint overpressure monitoring not running.134801DDS docking error.134802DDS undocking error.134803DDS bell cleaner error.134810DDS movement error.134811DDS movement error.134812DDS movement error.134813DDS movement error.134850DDS calibration error.134851DDS calibration error.135001Material change suspended.135002Material change cancelled.135003Material change resumed.135010Material change initialization error.135011Material change initialization error.135012Material change initialization error.135013Material change initialization error.135021Material change index file error.135022Material change index file error.135031Material change system index error.135041Material change cavity index error.135042Material change cavity index error.135051Material change sequence error.135052Material change sequence error.135053Material change sequence error.135054Material change sequence error.135055Material change sequence error.135061Material change signal error.135062Material change signal error.135063Material change signal error.135064Material change signal error.135071Material change alarm monitor error.135072Material change alarm monitor error.135073Material change alarm monitor error.135100Material change user error.